Reorganize the code to kill forward declarations of spi_nor_match_id()
macronix_quad_enable() and spi_nor_hwcaps_read2cmd().
Signed-off-by: Boris Brezillon <***@bootlin.com>
---
Changes in v3:
- Group all _quad_enable() implems
- Move spi_nor_hwcaps_xx2cmd() just after spi_nor_set_pp_settings()
Changes in v2:
- None
---
drivers/mtd/spi-nor/spi-nor.c | 614 +++++++++++++++++-----------------
1 file changed, 304 insertions(+), 310 deletions(-)
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index d099aee075e9..b440f29637ab 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -289,8 +289,6 @@ struct flash_info {
#define JEDEC_MFR(info) ((info)->id[0])
-static const struct flash_info *spi_nor_match_id(const char *name);
-
/*
* Read the status register, returning its value in the location
* Return the status register value.
@@ -1395,7 +1393,247 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
return ret;
}
-static int macronix_quad_enable(struct spi_nor *nor);
+/*
+ * Write status Register and configuration register with 2 bytes
+ * The first byte will be written to the status register, while the
+ * second byte will be written to the configuration register.
+ * Return negative if error occurred.
+ */
+static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
+{
+ int ret;
+
+ write_enable(nor);
+
+ ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
+ if (ret < 0) {
+ dev_err(nor->dev,
+ "error while writing configuration register\n");
+ return -EINVAL;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret) {
+ dev_err(nor->dev,
+ "timeout while writing configuration register\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * macronix_quad_enable() - set QE bit in Status Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Status Register.
+ *
+ * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int macronix_quad_enable(struct spi_nor *nor)
+{
+ int ret, val;
+
+ val = read_sr(nor);
+ if (val < 0)
+ return val;
+ if (val & SR_QUAD_EN_MX)
+ return 0;
+
+ write_enable(nor);
+
+ write_sr(nor, val | SR_QUAD_EN_MX);
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ ret = read_sr(nor);
+ if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
+ dev_err(nor->dev, "Macronix Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * spansion_quad_enable() - set QE bit in Configuraiton Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function is kept for legacy purpose because it has been used for a
+ * long time without anybody complaining but it should be considered as
+ * deprecated and maybe buggy.
+ * First, this function doesn't care about the previous values of the Status
+ * and Configuration Registers when it sets the QE bit (bit 1) in the
+ * Configuration Register: all other bits are cleared, which may have unwanted
+ * side effects like removing some block protections.
+ * Secondly, it uses the Read Configuration Register (35h) instruction though
+ * some very old and few memories don't support this instruction. If a pull-up
+ * resistor is present on the MISO/IO1 line, we might still be able to pass the
+ * "read back" test because the QSPI memory doesn't recognize the command,
+ * so leaves the MISO/IO1 line state unchanged, hence read_cr() returns 0xFF.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2] = {0, CR_QUAD_EN_SPAN};
+ int ret;
+
+ ret = write_sr_cr(nor, sr_cr);
+ if (ret)
+ return ret;
+
+ /* read back and check it */
+ ret = read_cr(nor);
+ if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
+ dev_err(nor->dev, "Spansion Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories not supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
+{
+ u8 sr_cr[2];
+ int ret;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_err(nor->dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+ sr_cr[1] = CR_QUAD_EN_SPAN;
+
+ return write_sr_cr(nor, sr_cr);
+}
+
+/**
+ * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Configuration Register.
+ * This function should be used with QSPI memories supporting the Read
+ * Configuration Register (35h) instruction.
+ *
+ * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
+ * memories.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spansion_read_cr_quad_enable(struct spi_nor *nor)
+{
+ struct device *dev = nor->dev;
+ u8 sr_cr[2];
+ int ret;
+
+ /* Check current Quad Enable bit value. */
+ ret = read_cr(nor);
+ if (ret < 0) {
+ dev_err(dev, "error while reading configuration register\n");
+ return -EINVAL;
+ }
+
+ if (ret & CR_QUAD_EN_SPAN)
+ return 0;
+
+ sr_cr[1] = ret | CR_QUAD_EN_SPAN;
+
+ /* Keep the current value of the Status Register. */
+ ret = read_sr(nor);
+ if (ret < 0) {
+ dev_err(dev, "error while reading status register\n");
+ return -EINVAL;
+ }
+ sr_cr[0] = ret;
+
+ ret = write_sr_cr(nor, sr_cr);
+ if (ret)
+ return ret;
+
+ /* Read back and check it. */
+ ret = read_cr(nor);
+ if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
+ dev_err(nor->dev, "Spansion Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * sr2_bit7_quad_enable() - set QE bit in Status Register 2.
+ * @nor: pointer to a 'struct spi_nor'
+ *
+ * Set the Quad Enable (QE) bit in the Status Register 2.
+ *
+ * This is one of the procedures to set the QE bit described in the SFDP
+ * (JESD216 rev B) specification but no manufacturer using this procedure has
+ * been identified yet, hence the name of the function.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int sr2_bit7_quad_enable(struct spi_nor *nor)
+{
+ u8 sr2;
+ int ret;
+
+ /* Check current Quad Enable bit value. */
+ ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1);
+ if (ret)
+ return ret;
+ if (sr2 & SR2_QUAD_EN_BIT7)
+ return 0;
+
+ /* Update the Quad Enable bit. */
+ sr2 |= SR2_QUAD_EN_BIT7;
+
+ write_enable(nor);
+
+ ret = nor->write_reg(nor, SPINOR_OP_WRSR2, &sr2, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error while writing status register 2\n");
+ return -EINVAL;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret < 0) {
+ dev_err(nor->dev, "timeout while writing status register 2\n");
+ return ret;
+ }
+
+ /* Read back and check it. */
+ ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1);
+ if (!(ret > 0 && (sr2 & SR2_QUAD_EN_BIT7))) {
+ dev_err(nor->dev, "SR2 Quad bit not set\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
/* Used when the "_ext_id" is two bytes at most */
#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
@@ -2002,248 +2240,6 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
return ret;
}
-/**
- * macronix_quad_enable() - set QE bit in Status Register.
- * @nor: pointer to a 'struct spi_nor'
- *
- * Set the Quad Enable (QE) bit in the Status Register.
- *
- * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
- *
- * Return: 0 on success, -errno otherwise.
- */
-static int macronix_quad_enable(struct spi_nor *nor)
-{
- int ret, val;
-
- val = read_sr(nor);
- if (val < 0)
- return val;
- if (val & SR_QUAD_EN_MX)
- return 0;
-
- write_enable(nor);
-
- write_sr(nor, val | SR_QUAD_EN_MX);
-
- ret = spi_nor_wait_till_ready(nor);
- if (ret)
- return ret;
-
- ret = read_sr(nor);
- if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
- dev_err(nor->dev, "Macronix Quad bit not set\n");
- return -EINVAL;
- }
-
- return 0;
-}
-
-/*
- * Write status Register and configuration register with 2 bytes
- * The first byte will be written to the status register, while the
- * second byte will be written to the configuration register.
- * Return negative if error occurred.
- */
-static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
-{
- int ret;
-
- write_enable(nor);
-
- ret = nor->write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
- if (ret < 0) {
- dev_err(nor->dev,
- "error while writing configuration register\n");
- return -EINVAL;
- }
-
- ret = spi_nor_wait_till_ready(nor);
- if (ret) {
- dev_err(nor->dev,
- "timeout while writing configuration register\n");
- return ret;
- }
-
- return 0;
-}
-
-/**
- * spansion_quad_enable() - set QE bit in Configuraiton Register.
- * @nor: pointer to a 'struct spi_nor'
- *
- * Set the Quad Enable (QE) bit in the Configuration Register.
- * This function is kept for legacy purpose because it has been used for a
- * long time without anybody complaining but it should be considered as
- * deprecated and maybe buggy.
- * First, this function doesn't care about the previous values of the Status
- * and Configuration Registers when it sets the QE bit (bit 1) in the
- * Configuration Register: all other bits are cleared, which may have unwanted
- * side effects like removing some block protections.
- * Secondly, it uses the Read Configuration Register (35h) instruction though
- * some very old and few memories don't support this instruction. If a pull-up
- * resistor is present on the MISO/IO1 line, we might still be able to pass the
- * "read back" test because the QSPI memory doesn't recognize the command,
- * so leaves the MISO/IO1 line state unchanged, hence read_cr() returns 0xFF.
- *
- * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
- * memories.
- *
- * Return: 0 on success, -errno otherwise.
- */
-static int spansion_quad_enable(struct spi_nor *nor)
-{
- u8 sr_cr[2] = {0, CR_QUAD_EN_SPAN};
- int ret;
-
- ret = write_sr_cr(nor, sr_cr);
- if (ret)
- return ret;
-
- /* read back and check it */
- ret = read_cr(nor);
- if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
- dev_err(nor->dev, "Spansion Quad bit not set\n");
- return -EINVAL;
- }
-
- return 0;
-}
-
-/**
- * spansion_no_read_cr_quad_enable() - set QE bit in Configuration Register.
- * @nor: pointer to a 'struct spi_nor'
- *
- * Set the Quad Enable (QE) bit in the Configuration Register.
- * This function should be used with QSPI memories not supporting the Read
- * Configuration Register (35h) instruction.
- *
- * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
- * memories.
- *
- * Return: 0 on success, -errno otherwise.
- */
-static int spansion_no_read_cr_quad_enable(struct spi_nor *nor)
-{
- u8 sr_cr[2];
- int ret;
-
- /* Keep the current value of the Status Register. */
- ret = read_sr(nor);
- if (ret < 0) {
- dev_err(nor->dev, "error while reading status register\n");
- return -EINVAL;
- }
- sr_cr[0] = ret;
- sr_cr[1] = CR_QUAD_EN_SPAN;
-
- return write_sr_cr(nor, sr_cr);
-}
-
-/**
- * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
- * @nor: pointer to a 'struct spi_nor'
- *
- * Set the Quad Enable (QE) bit in the Configuration Register.
- * This function should be used with QSPI memories supporting the Read
- * Configuration Register (35h) instruction.
- *
- * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
- * memories.
- *
- * Return: 0 on success, -errno otherwise.
- */
-static int spansion_read_cr_quad_enable(struct spi_nor *nor)
-{
- struct device *dev = nor->dev;
- u8 sr_cr[2];
- int ret;
-
- /* Check current Quad Enable bit value. */
- ret = read_cr(nor);
- if (ret < 0) {
- dev_err(dev, "error while reading configuration register\n");
- return -EINVAL;
- }
-
- if (ret & CR_QUAD_EN_SPAN)
- return 0;
-
- sr_cr[1] = ret | CR_QUAD_EN_SPAN;
-
- /* Keep the current value of the Status Register. */
- ret = read_sr(nor);
- if (ret < 0) {
- dev_err(dev, "error while reading status register\n");
- return -EINVAL;
- }
- sr_cr[0] = ret;
-
- ret = write_sr_cr(nor, sr_cr);
- if (ret)
- return ret;
-
- /* Read back and check it. */
- ret = read_cr(nor);
- if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
- dev_err(nor->dev, "Spansion Quad bit not set\n");
- return -EINVAL;
- }
-
- return 0;
-}
-
-/**
- * sr2_bit7_quad_enable() - set QE bit in Status Register 2.
- * @nor: pointer to a 'struct spi_nor'
- *
- * Set the Quad Enable (QE) bit in the Status Register 2.
- *
- * This is one of the procedures to set the QE bit described in the SFDP
- * (JESD216 rev B) specification but no manufacturer using this procedure has
- * been identified yet, hence the name of the function.
- *
- * Return: 0 on success, -errno otherwise.
- */
-static int sr2_bit7_quad_enable(struct spi_nor *nor)
-{
- u8 sr2;
- int ret;
-
- /* Check current Quad Enable bit value. */
- ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1);
- if (ret)
- return ret;
- if (sr2 & SR2_QUAD_EN_BIT7)
- return 0;
-
- /* Update the Quad Enable bit. */
- sr2 |= SR2_QUAD_EN_BIT7;
-
- write_enable(nor);
-
- ret = nor->write_reg(nor, SPINOR_OP_WRSR2, &sr2, 1);
- if (ret < 0) {
- dev_err(nor->dev, "error while writing status register 2\n");
- return -EINVAL;
- }
-
- ret = spi_nor_wait_till_ready(nor);
- if (ret < 0) {
- dev_err(nor->dev, "timeout while writing status register 2\n");
- return ret;
- }
-
- /* Read back and check it. */
- ret = nor->read_reg(nor, SPINOR_OP_RDSR2, &sr2, 1);
- if (!(ret > 0 && (sr2 & SR2_QUAD_EN_BIT7))) {
- dev_err(nor->dev, "SR2 Quad bit not set\n");
- return -EINVAL;
- }
-
- return 0;
-}
-
static int spi_nor_check(struct spi_nor *nor)
{
if (!nor->dev || !nor->read || !nor->write ||
@@ -2318,6 +2314,57 @@ spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
pp->proto = proto;
}
+static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size)
+{
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ if (table[i][0] == (int)hwcaps)
+ return table[i][1];
+
+ return -EINVAL;
+}
+
+static int spi_nor_hwcaps_read2cmd(u32 hwcaps)
+{
+ static const int hwcaps_read2cmd[][2] = {
+ { SNOR_HWCAPS_READ, SNOR_CMD_READ },
+ { SNOR_HWCAPS_READ_FAST, SNOR_CMD_READ_FAST },
+ { SNOR_HWCAPS_READ_1_1_1_DTR, SNOR_CMD_READ_1_1_1_DTR },
+ { SNOR_HWCAPS_READ_1_1_2, SNOR_CMD_READ_1_1_2 },
+ { SNOR_HWCAPS_READ_1_2_2, SNOR_CMD_READ_1_2_2 },
+ { SNOR_HWCAPS_READ_2_2_2, SNOR_CMD_READ_2_2_2 },
+ { SNOR_HWCAPS_READ_1_2_2_DTR, SNOR_CMD_READ_1_2_2_DTR },
+ { SNOR_HWCAPS_READ_1_1_4, SNOR_CMD_READ_1_1_4 },
+ { SNOR_HWCAPS_READ_1_4_4, SNOR_CMD_READ_1_4_4 },
+ { SNOR_HWCAPS_READ_4_4_4, SNOR_CMD_READ_4_4_4 },
+ { SNOR_HWCAPS_READ_1_4_4_DTR, SNOR_CMD_READ_1_4_4_DTR },
+ { SNOR_HWCAPS_READ_1_1_8, SNOR_CMD_READ_1_1_8 },
+ { SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 },
+ { SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 },
+ { SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR },
+ };
+
+ return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd,
+ ARRAY_SIZE(hwcaps_read2cmd));
+}
+
+static int spi_nor_hwcaps_pp2cmd(u32 hwcaps)
+{
+ static const int hwcaps_pp2cmd[][2] = {
+ { SNOR_HWCAPS_PP, SNOR_CMD_PP },
+ { SNOR_HWCAPS_PP_1_1_4, SNOR_CMD_PP_1_1_4 },
+ { SNOR_HWCAPS_PP_1_4_4, SNOR_CMD_PP_1_4_4 },
+ { SNOR_HWCAPS_PP_4_4_4, SNOR_CMD_PP_4_4_4 },
+ { SNOR_HWCAPS_PP_1_1_8, SNOR_CMD_PP_1_1_8 },
+ { SNOR_HWCAPS_PP_1_8_8, SNOR_CMD_PP_1_8_8 },
+ { SNOR_HWCAPS_PP_8_8_8, SNOR_CMD_PP_8_8_8 },
+ };
+
+ return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd,
+ ARRAY_SIZE(hwcaps_pp2cmd));
+}
+
/*
* Serial Flash Discoverable Parameters (SFDP) parsing.
*/
@@ -2527,8 +2574,6 @@ static const struct sfdp_bfpt_erase sfdp_bfpt_erases[] = {
{BFPT_DWORD(9), 16},
};
-static int spi_nor_hwcaps_read2cmd(u32 hwcaps);
-
/**
* spi_nor_set_erase_type() - set a SPI NOR erase type
* @erase: pointer to a structure that describes a SPI NOR erase type
@@ -3342,57 +3387,6 @@ static int spi_nor_init_params(struct spi_nor *nor,
return 0;
}
-static int spi_nor_hwcaps2cmd(u32 hwcaps, const int table[][2], size_t size)
-{
- size_t i;
-
- for (i = 0; i < size; i++)
- if (table[i][0] == (int)hwcaps)
- return table[i][1];
-
- return -EINVAL;
-}
-
-static int spi_nor_hwcaps_read2cmd(u32 hwcaps)
-{
- static const int hwcaps_read2cmd[][2] = {
- { SNOR_HWCAPS_READ, SNOR_CMD_READ },
- { SNOR_HWCAPS_READ_FAST, SNOR_CMD_READ_FAST },
- { SNOR_HWCAPS_READ_1_1_1_DTR, SNOR_CMD_READ_1_1_1_DTR },
- { SNOR_HWCAPS_READ_1_1_2, SNOR_CMD_READ_1_1_2 },
- { SNOR_HWCAPS_READ_1_2_2, SNOR_CMD_READ_1_2_2 },
- { SNOR_HWCAPS_READ_2_2_2, SNOR_CMD_READ_2_2_2 },
- { SNOR_HWCAPS_READ_1_2_2_DTR, SNOR_CMD_READ_1_2_2_DTR },
- { SNOR_HWCAPS_READ_1_1_4, SNOR_CMD_READ_1_1_4 },
- { SNOR_HWCAPS_READ_1_4_4, SNOR_CMD_READ_1_4_4 },
- { SNOR_HWCAPS_READ_4_4_4, SNOR_CMD_READ_4_4_4 },
- { SNOR_HWCAPS_READ_1_4_4_DTR, SNOR_CMD_READ_1_4_4_DTR },
- { SNOR_HWCAPS_READ_1_1_8, SNOR_CMD_READ_1_1_8 },
- { SNOR_HWCAPS_READ_1_8_8, SNOR_CMD_READ_1_8_8 },
- { SNOR_HWCAPS_READ_8_8_8, SNOR_CMD_READ_8_8_8 },
- { SNOR_HWCAPS_READ_1_8_8_DTR, SNOR_CMD_READ_1_8_8_DTR },
- };
-
- return spi_nor_hwcaps2cmd(hwcaps, hwcaps_read2cmd,
- ARRAY_SIZE(hwcaps_read2cmd));
-}
-
-static int spi_nor_hwcaps_pp2cmd(u32 hwcaps)
-{
- static const int hwcaps_pp2cmd[][2] = {
- { SNOR_HWCAPS_PP, SNOR_CMD_PP },
- { SNOR_HWCAPS_PP_1_1_4, SNOR_CMD_PP_1_1_4 },
- { SNOR_HWCAPS_PP_1_4_4, SNOR_CMD_PP_1_4_4 },
- { SNOR_HWCAPS_PP_4_4_4, SNOR_CMD_PP_4_4_4 },
- { SNOR_HWCAPS_PP_1_1_8, SNOR_CMD_PP_1_1_8 },
- { SNOR_HWCAPS_PP_1_8_8, SNOR_CMD_PP_1_8_8 },
- { SNOR_HWCAPS_PP_8_8_8, SNOR_CMD_PP_8_8_8 },
- };
-
- return spi_nor_hwcaps2cmd(hwcaps, hwcaps_pp2cmd,
- ARRAY_SIZE(hwcaps_pp2cmd));
-}
-
static int spi_nor_select_read(struct spi_nor *nor,
const struct spi_nor_flash_parameter *params,
u32 shared_hwcaps)
@@ -3669,6 +3663,18 @@ void spi_nor_restore(struct spi_nor *nor)
}
EXPORT_SYMBOL_GPL(spi_nor_restore);
+static const struct flash_info *spi_nor_match_id(const char *name)
+{
+ const struct flash_info *id = spi_nor_ids;
+
+ while (id->name) {
+ if (!strcmp(name, id->name))
+ return id;
+ id++;
+ }
+ return NULL;
+}
+
int spi_nor_scan(struct spi_nor *nor, const char *name,
const struct spi_nor_hwcaps *hwcaps)
{
@@ -3872,18 +3878,6 @@ int spi_nor_scan(struct spi_nor *nor, const char *name,
}
EXPORT_SYMBOL_GPL(spi_nor_scan);
-static const struct flash_info *spi_nor_match_id(const char *name)
-{
- const struct flash_info *id = spi_nor_ids;
-
- while (id->name) {
- if (!strcmp(name, id->name))
- return id;
- id++;
- }
- return NULL;
-}
-
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Huang Shijie <***@gmail.com>");
MODULE_AUTHOR("Mike Lavender");
--
2.17.1